configuration information with no manual intervention. of the Cisco Aironet AG Series allows the access point to be placed above ceilings in plenum. To clear or remove the manually entered controller information, you can use these EXEC. installed in accordance with Cisco’s installation instructions, it may cause interference with radio and television reception. This equipment has.

Author: Kazik Vigul
Country: Guadeloupe
Language: English (Spanish)
Genre: Sex
Published (Last): 23 May 2007
Pages: 412
PDF File Size: 7.59 Mb
ePub File Size: 2.43 Mb
ISBN: 629-3-28102-541-7
Downloads: 8934
Price: Free* [*Free Regsitration Required]
Uploader: Dot


Launch your browser, and go to this URL: For full operation, the access point requires Proper installation of this radio according to the instructions found in this manual will result in user exposure that is substantially below the FCC recommended limits. None required — 1. Figure shows an access point in an all-wireless network. This device must accept any interference received, including interference that may cause undesired operation. Page 38 IP address and shared secret for an authentication server on your network server authentication port Clear Clears the selected options on the page.

Push or pull the excess cable length the loop back through the access point cable bay area. Figure shows an access point acting as a repeater.

Support for Intelligent Power Management might not be currently available for your Cisco power source. Page The body responsible for the Ethernet You can use the LED colors to assess the unit status. Step 4 Figure shows the Summary Status page.


An Enter Network Password screen appears. The following topic is covered in this appendix: Running The Carrier Busy Test If you want to specify the number of packets to use in the test, follow these steps: Page 94 None required — 1. Each Cisco switch should be upgraded to support Intelligent Power Management.

Aironet Wireless Software Display Tables. Insert the security cable latch into the security cable slot on the ciscp point. Department Of Communications-canada This device must accept cico interference received, including interference that may cause undesired operation.

Don’t have an account? Page 50 – Connecting to mnaual Ethernet Network with L Figure shows the locations of the three LEDs.

The body responsible for the Ethernet If you press Esc Y more than ten times, you cycle to the first buffer entry.

By pressing ‘print’ button you will print only current page. If you want to specify the number of packets to use in the test, follow these steps: Express Security Limitations Because the Express Security page is designed for simple configuration of basic security, the options available are a subset of the access point security capabilities.

The default password is Cisco. Disconnect power from the access point the power jack for external power or the Ethernet cable for in-line power. The Cisco Products page appears. The default Step 4 username is Cisco, and the default password is Cisco. Aironet Extensions By default, the access point uses Cisco Aironet To move back to the beginning of the command entry, press Ctrl-B or the left arrow key repeatedly.


Click Apply to save your settings.

Cisco Aironet 1130AG Quick Start Manual

Hvis du vil se oversettelser av de advarslene som finnes i denne publikasjonen, kan du se i vedlegget “Translated Safety Warnings” [Oversatte sikkerhetsadvarsler]. Follow these steps to access them: Page 33 SSIDs 1130a eliminate the conflict. The commands available to you depend on the mode you are currently using.

A small window appears containing a partial listing of wireless products. If you need to continue configuring the access point using Telnet, use the new IP address to open another Telnet session to the access point.

Using inline power, you do not need to run a power cord to the access point because power is supplied over the Ethernet cable.

Cisco Aironet 1130AG Hardware Installation Manual

You can also press Ctrl-A to immediately move to the beginning of the line. Preface Audience This guide is for the networking professional who installs and manages the Cisco Aironet AG Series Ciscl Point, hereafter referred to as the access point.

Mxnual you have mounted the access point, its padlock post enables you to protect the Ethernet, power cables, and Mode button, and to lock the access point with a padlock. Close the access point cover by sliding it over the cable bay area until you hear a click.