ASTM D5430-93 PDF

ASTM D() Standard Test Methods for Visually Inspecting and Grading Fabrics Scope These test methods describe a procedure to. Four-Point System: Four-Point System, a standard established under ASTM D – 07(), is a standardized Test Methods for fabric. Home; ASTM D(). standard by ASTM International, 07/ 15/ View all product details ASTM D(). March

Author: Vogami Musho
Country: Uzbekistan
Language: English (Spanish)
Genre: Marketing
Published (Last): 24 September 2012
Pages: 265
PDF File Size: 18.60 Mb
ePub File Size: 6.31 Mb
ISBN: 298-7-11490-313-6
Downloads: 20561
Price: Free* [*Free Regsitration Required]
Uploader: Taurg

In the apparel and textile industry, textile mills, apparel brands and buyers set their own standards for acceptable points.

Fabric Inspection | Four Point System

No penalty points are assigned to minor defects. Following defects will be penalized penalty points as per rules: Fabric width will be checked minimum of three times during the inspection of a piece beginning, middle and end of a piece. Use tally marking for recording of number of defects. One more thing you should remember that acceptable points can be defined as points per linear yards as well as points per square yards.

Types of defects found in fabric. No penalty points are recorded or assigned for minor defects.

A check sheet includes general details, details of fabric lot, fabric defects according their sizes, summary of fabric defects, quantity inspected and total penalty points and result of the fabric lot after inspection. D54300-93 26, Md Sohanur Rahman Sobuj 0. Holes and openings the largest dimension.


Some fabric defects are given below:. A sample 4 point system fabric inspection format has been attached at the bottom.

ASTM D – 93() Standard Test Methods for Visually Inspecting and Grading Fabrics

Secondly, acceptable points for individual roll and acceptable average points of all roll are set at different level. Disperse Dye for Polyester Why called disperse dye Application and mechanism of disperse dyes Features of of disperse dyes October 15, Fatema Sharmin d4530-93. Fabric checker should know common defects found in fabrics and he must recognize defects on the fabric at the time of fabric inspection.

A defect can be measured either length or width direction; the system remains the same. Major knitted fabric defects.

Again grading is done based number of penalty points per square yards. A fabric roll yards long and 46 inch wide contains following defects. There are various fabric d5430-3 systems such as. Fabric Inspection Four point system. Progressive Bundle System April 7, Md. This width is excluding selvedge. Check sheet or Inspection Sstm. Latest posts by Md. Four-Point System is widest acceptance in fabric inspection due to its practical, impartial, and worldwide recognized.

A standards level is set by ASTM. Only major defects are taking into account.


The Quality Inspector may include any other defect which he feels are of a major category and may forward such defect details to the customer for feed back as and when required. Major woven fabric defects. Omar Faruk see all. Whenever errors are recognized during fabric inspection under 4 points system and defect must be assigned a number of points depending on the severity or length.


Fabric Inspection | Four Point System | Textile Study Center

A serious defect is any defect that would cause a final garment to be considered a second. Powered by Facebook Comments. Only major errors are considered. Following defects are cut table and will be rejected: Many used to say that up to 40 points per square yards is acceptable. So, defect is acceptable. Only major defects are considered.

Bar tack D5430-3 Machine II Study on d5403-93 tack sewing machine with thread path diagram and sample production. Calculation of total points per yards. Fabric is inspected to determine its acceptability from a quality view point. To record or to collects defects during inspection a simple check sheet must b used.

Major dye or printing defects. Pieces having a width of measurement of less than the specified purchased width shall be graded as second quality. To use this system someone have to know following things: No more than 4 penalty points is assigned for any single flaw.